Module Details

Module Code: MARI6005
Title: Technical Drawing 2
Long Title: Technical Drawing 2
NFQ Level: Fundamental
Valid From: Semester 1 - 2015/16 ( September 2015 )
Duration: 1 Semester
Credits: 5
Field of Study: 5252 - Marine Engineering
Module Delivered in: 2 programme(s)
Module Description: This module builds on the knowledge gained from the module Technical Drawing 1. Students using manual drawing equipment will produce a portfolio of drawings based on the engineering drawing topics taught. This module introduces the student to Computer Aided Design (CAD) Software.
 
Learning Outcomes
On successful completion of this module the learner will be able to:
# Learning Outcome Description
LO1 Apply appropriate technical drawing methodologies in order to successfully produce drawing solutions.
LO2 Apply appropriate international drawing standards.
LO3 Display accuracy, attention to detail and neatness in the drawings produced.
LO4 Produce a portfolio of Engineering drawings based upon the topics taught during this module.
LO5 Produce a portfolio of Computer Aided Design (CAD) engineering drawings
Dependencies
Module Recommendations

This is prior learning (or a practical skill) that is strongly recommended before enrolment in this module. You may enrol in this module if you have not acquired the recommended learning but you will have considerable difficulty in passing (i.e. achieving the learning outcomes of) the module. While the prior learning is expressed as named MTU module(s) it also allows for learning (in another module or modules) which is equivalent to the learning specified in the named module(s).
10653 MARI6004 Technical Drawing 1
Incompatible Modules
These are modules which have learning outcomes that are too similar to the learning outcomes of this module. You may not earn additional credit for the same learning and therefore you may not enrol in this module if you have successfully completed any modules in the incompatible list.
No incompatible modules listed
Co-requisite Modules
No Co-requisite modules listed
Requirements

This is prior learning (or a practical skill) that is mandatory before enrolment in this module is allowed. You may not enrol on this module if you have not acquired the learning specified in this section.
No requirements listed
 
Indicative Content
Loci & Linkage
Construction of the following Loci: Involutes, Archimedean Spiral, Helix and Cycloid. Draw the controlled movement of a point on a link incorporated in a mechanism. Construction of suitable guards for the mechanism in which the loci has been established.
Gear & Cam Drives
Construction of Gears based on the Module of the gear. Construction of Cams using Uniform Acceleration & Retardation, Uniform Velocity & Simple Harmonic Motion. Construction of Cam Displacement Diagrams
Developments
Developments of components including; Pipework, Cones and Transitions.
CAD Techniques
Two Dimensional drawing and editing, Layers, Dimensioning, Hatch patterns, Plotting.
Sections & Developments
Cutting Planes, Sectioning of Singular Engineering Components. Development of Pipework Components.
Assembly Drawing with Sectional View
1st Angle Orthographic Projection Assembly Drawings including Sectional Views. Conventional representations of machine parts commonly found in Engineering Assembly drawings, e.g. Hexagonal Nuts and Bolts, Washers, Springs, Circlips and others.
Module Content & Assessment
Assessment Breakdown%
Coursework100.00%

Assessments

Coursework
Assessment Type Practical/Skills Evaluation % of Total Mark 20
Timing Week 4 Learning Outcomes 1,3,4
Assessment Description
Drawing Assessment - Machine Components
Assessment Type Practical/Skills Evaluation % of Total Mark 30
Timing Week 6 Learning Outcomes 1,3,4
Assessment Description
Drawing Assessment - Assembly
Assessment Type Practical/Skills Evaluation % of Total Mark 20
Timing Week 10 Learning Outcomes 1,3,5
Assessment Description
CAD Assessment - Computer Aided Design Techniques
Assessment Type Practical/Skills Evaluation % of Total Mark 30
Timing Sem End Learning Outcomes 1,3,5
Assessment Description
CAD Assessment - Assembly Drawing with Sectional View
No End of Module Formal Examination
Reassessment Requirement
Coursework Only
This module is reassessed solely on the basis of re-submitted coursework. There is no repeat written examination.

The University reserves the right to alter the nature and timings of assessment

 

Module Workload

Workload: Full Time
Workload Type Contact Type Workload Description Frequency Average Weekly Learner Workload Hours
Lab Contact Machinev Drawing Every Week 2.00 2
Independent & Directed Learning (Non-contact) Non Contact Machine Drawing/Cad Every Week 3.00 3
Lab Contact CAD Every Week 2.00 2
Total Hours 7.00
Total Weekly Learner Workload 7.00
Total Weekly Contact Hours 4.00
This module has no Part Time workload.
 
Module Resources
Recommended Book Resources
  • C.Simmons & D.Maguire. (1974), A manual of Engineering Drawing Practices,, 1st. English Universities Press Ltd, Liverpool, [ISBN: 0340179961].
  • M.Parker & F.Pickup. (1960), Engineering Drawing with worked examples 2, 3rd. Stanley Thornes Ltd, Musselborough, [ISBN: 0748410401].
  • E. O'Broin. (1991), Technical Draughtmanship, 2nd. Gill & McMillan, Dublin, [ISBN: 0717116522].
  • M.Parker & F.Pickup. (1972), Engineering Drawing with worked examples 1, 3rd. Stanley Thornes Ltd, London, [ISBN: 074870311].
Recommended Article/Paper Resources
  • British Standards 2005, Engineering Drawing Practice.
This module does not have any other resources
 
Module Delivered in
Programme Code Programme Semester Delivery
CR_EMAEL_7 Bachelor of Engineering in Marine Electrotechnology 2 Mandatory
CR_EMARE_7 Bachelor of Engineering in Marine Engineering 2 Mandatory