Module Details

Module Code: MARI6004
Title: Technical Drawing 1
Long Title: Technical Drawing 1
NFQ Level: Fundamental
Valid From: Semester 1 - 2015/16 ( September 2015 )
Duration: 1 Semester
Credits: 5
Field of Study: 5252 - Marine Engineering
Module Delivered in: 2 programme(s)
Module Description: This module introduces students to Technical Drawing of an Engineering aspect. Students using manual drawing equipment will produce a portfolio of drawings based on the engineering drawing topics taught.
 
Learning Outcomes
On successful completion of this module the learner will be able to:
# Learning Outcome Description
LO1 Apply international drawing standards.
LO2 Use 1st Angle Orthographic Projection drawing principles through the completion of drawings.
LO3 Produce Engineering Drawings based upon topics taught in the module
LO4 Apply appropriate technical drawing methodologies in order to successfully produce assembly drawing solutions.
LO5 Display attention to detail and overall neatness in each drawing produced.
Dependencies
Module Recommendations

This is prior learning (or a practical skill) that is strongly recommended before enrolment in this module. You may enrol in this module if you have not acquired the recommended learning but you will have considerable difficulty in passing (i.e. achieving the learning outcomes of) the module. While the prior learning is expressed as named MTU module(s) it also allows for learning (in another module or modules) which is equivalent to the learning specified in the named module(s).
Incompatible Modules
These are modules which have learning outcomes that are too similar to the learning outcomes of this module. You may not earn additional credit for the same learning and therefore you may not enrol in this module if you have successfully completed any modules in the incompatible list.
No incompatible modules listed
Co-requisite Modules
No Co-requisite modules listed
Requirements

This is prior learning (or a practical skill) that is mandatory before enrolment in this module is allowed. You may not enrol on this module if you have not acquired the learning specified in this section.
No requirements listed
 
Indicative Content
Drawing Standards
Relevant Drawing Standards, Drawing Conventions, Line Types, Line Thicknesses. Relevant Component Standards; Fasteners, Threads
1st Angle Orthographic Projection
Drawings of Singular Engineering Components showing Front Elevation, Plan and End View. Associated Orthographic Projection Symbol.
Sectioning
Cutting Planes, Sectioning of Singular Engineering Components.
Engineering Assembly Drawings
1st Angle Orthographic Projection Assembly Drawings to include Sectioning, Dimensioning, Labelling, Parts List and the Orthographic Projection Symbol
Isometric Projection
Engineering Components shown in 2D Orthographic views drawn in 3D using Isometric Projection.
Module Content & Assessment
Assessment Breakdown%
Coursework100.00%

Assessments

Coursework
Assessment Type Practical/Skills Evaluation % of Total Mark 15
Timing Week 3 Learning Outcomes 3
Assessment Description
Drawing Assessment - 1st Angle Orthographic Projection
Assessment Type Practical/Skills Evaluation % of Total Mark 35
Timing Week 9 Learning Outcomes 3,4
Assessment Description
Drawing Assessment - Assembly Drawing with Section View
Assessment Type Practical/Skills Evaluation % of Total Mark 50
Timing Sem End Learning Outcomes 3
Assessment Description
Drawing Assessment - All topics listed above
No End of Module Formal Examination
Reassessment Requirement
Coursework Only
This module is reassessed solely on the basis of re-submitted coursework. There is no repeat written examination.

The University reserves the right to alter the nature and timings of assessment

 

Module Workload

Workload: Full Time
Workload Type Contact Type Workload Description Frequency Average Weekly Learner Workload Hours
Lab Contact Syllabus and Assessments Every Week 4.00 4
Independent & Directed Learning (Non-contact) Non Contact Machine Drawing Every Week 3.00 3
Total Hours 7.00
Total Weekly Learner Workload 7.00
Total Weekly Contact Hours 4.00
This module has no Part Time workload.
 
Module Resources
Recommended Book Resources
  • C.Simmons & D.Maguire. (1974), A Manual of Engineering Drawing Practice, 1st. English Universities Press Ltd, Liverpool, [ISBN: 0340179961].
  • M.Parker & F.Pickup. (1960), Engineering Drawing with worked examples 1, 3rd. Stanley Thornes Ltd, London, [ISBN: 074870311].
  • E.O'Broin. (1991), Technical Draughtmanship, 2nd. Gill & McMillan, Dublin, [ISBN: 0717116522].
Supplementary Book Resources
  • M.Parker & F.Pickup. (1972), Engineering Drawing with worked examples 2, 3rd. Stanley Thornes Ltd, Musselburgh, [ISBN: 074871040].
Recommended Article/Paper Resources
  • British Standards 2005, Engineering Drawing Practice.
This module does not have any other resources
 
Module Delivered in
Programme Code Programme Semester Delivery
CR_EMAEL_7 Bachelor of Engineering in Marine Electrotechnology 1 Mandatory
CR_EMARE_7 Bachelor of Engineering in Marine Engineering 1 Mandatory