Module Details

Module Code: MECH6004
Title: CAD & Mechanical Design
Long Title: CAD & Mechanical Design
NFQ Level: Fundamental
Valid From: Semester 1 - 2016/17 ( September 2016 )
Duration: 1 Semester
Credits: 5
Field of Study: 5211 - Mechanical Engineering
Module Delivered in: 2 programme(s)
Module Description: This module gives the student advanced 3D Modelling techniques. The students are also exposed to component design. Teams of students will undertake a project which will involve analysis, design and presentation segments.
 
Learning Outcomes
On successful completion of this module the learner will be able to:
# Learning Outcome Description
LO1 Develop 3D models/assemblies with industry specific 3D parametric modelling software.
LO2 Produce 2D working drawings from 3D parametric models.
LO3 Apply functional design to generate digital prototypes incorporating best engineering practises and identifying ethical/environmental impact considerations.
LO4 Analyse/redesign an existing mechanical system
LO5 Design,test and report on a system as part of a team.
Dependencies
Module Recommendations

This is prior learning (or a practical skill) that is strongly recommended before enrolment in this module. You may enrol in this module if you have not acquired the recommended learning but you will have considerable difficulty in passing (i.e. achieving the learning outcomes of) the module. While the prior learning is expressed as named MTU module(s) it also allows for learning (in another module or modules) which is equivalent to the learning specified in the named module(s).
Incompatible Modules
These are modules which have learning outcomes that are too similar to the learning outcomes of this module. You may not earn additional credit for the same learning and therefore you may not enrol in this module if you have successfully completed any modules in the incompatible list.
No incompatible modules listed
Co-requisite Modules
No Co-requisite modules listed
Requirements

This is prior learning (or a practical skill) that is mandatory before enrolment in this module is allowed. You may not enrol on this module if you have not acquired the learning specified in this section.
No requirements listed
 
Indicative Content
3D Solid Modelling
Design of advanced solid models features (e.g.: Offset edges tools, Sweeps, Blends (Lofts), Shell, Draft, Rib and Thin; Relations and Parameters.)Assembly of parts (e.g.: project folder, content centre,B.O.M). The use of 3D modelling techniques for sheet metal design, shaft, bearing and spring selection, ethical design through material and Environmental considerations.
Machine Component Design
Simple Machine Design. Selection and use of chain drives, electric motors, variable speed drives, coupling, fasteners and welded joints.
Limits and Fits
Basic Size, Deviation, Tolerance, Shaft Basis System, Hole Basis System, I.S. EN 20286.Geometrical Product Specifications EN iso11-1.
Module Content & Assessment
Assessment Breakdown%
Coursework100.00%

Assessments

Coursework
Assessment Type Practical/Skills Evaluation % of Total Mark 10
Timing Week 5 Learning Outcomes 1,2
Assessment Description
3D solid model assesment
Assessment Type Open-book Examination % of Total Mark 20
Timing Week 7 Learning Outcomes 4
Assessment Description
Component Selection Design Assesment
Assessment Type Practical/Skills Evaluation % of Total Mark 10
Timing Week 10 Learning Outcomes 1,2,3
Assessment Description
3D solid model digital assessment
Assessment Type Project % of Total Mark 40
Timing Sem End Learning Outcomes 4,5
Assessment Description
Design reports (based on team research,design and laboratory testing)
Assessment Type Practical/Skills Evaluation % of Total Mark 20
Timing Sem End Learning Outcomes 1,2,3
Assessment Description
portfolio of 3D CAD models/ 2D working drawings / project
No End of Module Formal Examination
Reassessment Requirement
Repeat the module
The assessment of this module is inextricably linked to the delivery. The student must reattend the module in its entirety in order to be reassessed.

The University reserves the right to alter the nature and timings of assessment

 

Module Workload

Workload: Full Time
Workload Type Contact Type Workload Description Frequency Average Weekly Learner Workload Hours
Lab Contact 3D CAD Every Week 2.00 2
Lecture Contact Design Every Week 3.00 3
Independent & Directed Learning (Non-contact) Non Contact No Description Every Week 2.00 2
Total Hours 7.00
Total Weekly Learner Workload 7.00
Total Weekly Contact Hours 5.00
Workload: Part Time
Workload Type Contact Type Workload Description Frequency Average Weekly Learner Workload Hours
Lab Contact 3D CAD Every Week 2.00 2
Lecturer-Supervised Learning (Contact) Contact Design Every Week 3.00 3
Independent & Directed Learning (Non-contact) Non Contact No Description Every Week 2.00 2
Total Hours 7.00
Total Weekly Learner Workload 7.00
Total Weekly Contact Hours 5.00
 
Module Resources
Recommended Book Resources
  • Robert L Mott. (2013), Machine Elements in Mechanical Design, 5th Edition. Prentice Hall, [ISBN: 978-0135077931].
Supplementary Book Resources
  • James D.Bethune. (2014), Engineering Design Graphics with Autodesk® Inventor® 2015, Pearson - prentice hall, [ISBN: 0131592254].
  • Amiss et al. (1996), Machinery's Handbook Guide: Guide to the Use of Tables and Formulas in Machinery's Handbook, 25th. Industrial Press, New York, N.Y., [ISBN: 0831124997 : 2.95].
  • Roy D. Cullum. (1988), Handbook of engineering design, Butterworths, London, [ISBN: 0408005580].
  • Gitin M. Maitra and L.V. Prasad. (1985), Handbook of mechanical design, Tata McGraw-Hill, New Delhi. London, [ISBN: 0074517589].
This module does not have any article/paper resources
Other Resources
 
Module Delivered in
Programme Code Programme Semester Delivery
CR_EMECH_8 Bachelor of Engineering (Honours) in Mechanical Engineering 2 Mandatory
CR_EOMNI_8 Engineering Common Entry (Level 8) 2 Elective