AUTO7011 - Automotive Diagnostic Systems

Module Details

Module Code: AUTO7011
Title: Automotive Diagnostic Systems
Long Title: Automotive Diagnostic Systems
NFQ Level: Intermediate
Valid From: Semester 1 - 2016/17 ( September 2016 )
Duration: 1 Semester
Credits: 5
Field of Study: 5251 - Automotive Engineering
Module Delivered in: 2 programme(s)
Module Description: This module is designed to give the student a practical knowledge of up to date equipment used in workshops to carry out various diagnostic tests on modern vehicles.
 
Learning Outcomes
On successful completion of this module the learner will be able to:
# Learning Outcome Description
LO1 Evaluate engine performance via the use of modern engine test equipment in compliance with current Health & Safety practices.
LO2 Interpret the various steering geometry angles by use of steering diagnostic test equipment in compliance with current Health & Safety practices.
LO3 Operate various vehicle auxillary systems with suitable diagnostic test equipment in compliance with current Health & Safety practices.
LO4 Determine mechanical/electrical faults using diagnostic test equipment in compliance with current Health & Saftety pracices
Dependencies
Module Recommendations

This is prior learning (or a practical skill) that is strongly recommended before enrolment in this module. You may enrol in this module if you have not acquired the recommended learning but you will have considerable difficulty in passing (i.e. achieving the learning outcomes of) the module. While the prior learning is expressed as named MTU module(s) it also allows for learning (in another module or modules) which is equivalent to the learning specified in the named module(s).

Incompatible Modules
These are modules which have learning outcomes that are too similar to the learning outcomes of this module. You may not earn additional credit for the same learning and therefore you may not enrol in this module if you have successfully completed any modules in the incompatible list.
No incompatible modules listed
Co-requisite Modules
No Co-requisite modules listed
Requirements

This is prior learning (or a practical skill) that is mandatory before enrolment in this module is allowed. You may not enrol on this module if you have not acquired the learning specified in this section.

No requirements listed
 
Indicative Content
Engine Diagnostic
Cylinder compression testing, Cylinder leakage testing, Coolant system testing, measurement dianostics.
Brake Systems Diagnostics.
A.B.S circuit testing.Component and sensor testing.Brake fluid testing.Brake vacumn testing.
Vehicle Testing Procedures (National standards)
Demonstrate the procedure in carrying out a test on a vehicle compatible with that of a NCT test.
Steering and Suspension
Electronic steering systems 4 wheel alignment procedures
Petrol fuel injection systems.
Dismantle , identify, reassemble, and test petrol injection system on a spark ignition engines.
Computer Control/Management Systems
Diagnostic procedures with the aid of an oscilloscope, wave form analysis, Automotive diagnostic hardware and software solutions, Emission diagnostics, Component testing, EOBD compliance systems, Chassis Component Diagnostics.
In Vehicle Networks
Examine in vehicle networks; identify the network layout and its active components. Diagnose basic mechanical /physical fault, use scan tool to display fault location presence of CAN signal faults, identify /description, rectify and clear fault memory.
Compression Ignition Fuel Systems
Dismantle, identify, and reassemble, fuel systems on compression ignition engines. Using a serial communication Diagnostic tester, interrogate the ECU for DTCS. Erase DTCS and display live data for common rail engines.
Transmission.
Dismantle, identify and reassemble Manual/Tiptronic/Automatic/ 4-Wheel Drive transmission systems.
Module Content & Assessment
Assessment Breakdown%
Coursework100.00%

Assessments

Coursework
Assessment Type Practical/Skills Evaluation % of Total Mark 25
Timing Week 4 Learning Outcomes 1
Assessment Description
Engine Diagnostic
Assessment Type Practical/Skills Evaluation % of Total Mark 25
Timing Week 6 Learning Outcomes 3
Assessment Description
Brake systems diagnostics
Assessment Type Practical/Skills Evaluation % of Total Mark 25
Timing Week 9 Learning Outcomes 2,3
Assessment Description
Steering Geometry & Vehicle Auxiliary Systems diagnostics.
Assessment Type Practical/Skills Evaluation % of Total Mark 25
Timing Sem End Learning Outcomes 4
Assessment Description
CAN diagnostics
No End of Module Formal Examination
Reassessment Requirement
Repeat the module
The assessment of this module is inextricably linked to the delivery. The student must reattend the module in its entirety in order to be reassessed.

The University reserves the right to alter the nature and timings of assessment

 

Module Workload

Workload: Full Time
Workload Type Contact Type Workload Description Frequency Average Weekly Learner Workload Hours
Lab Contact Formal Lab Work Every Week 4.00 4
Independent & Directed Learning (Non-contact) Non Contact Self Directed Learning Every Week 3.00 3
Total Hours 7.00
Total Weekly Learner Workload 7.00
Total Weekly Contact Hours 4.00
Workload: Part Time
Workload Type Contact Type Workload Description Frequency Average Weekly Learner Workload Hours
Lab Contact Formal Lab Work Every Week 3.00 3
Independent & Directed Learning (Non-contact) Non Contact No Description Every Week 4.00 4
Total Hours 7.00
Total Weekly Learner Workload 7.00
Total Weekly Contact Hours 3.00
 
Module Resources
Recommended Book Resources
  • Alma Hillier. (2014), Hillier's Fundamentals of Automotive Electronics Book 2., Nelson Thornes, p.448, [ISBN: 978-1-4085-1537-2].
Supplementary Book Resources
  • Tom Denton. (2011), Automotive mechanical and electrical systems, Elsevier, [ISBN: 0080969453].
This module does not have any article/paper resources
Other Resources
 
Module Delivered in
Programme Code Programme Semester Delivery
CR_EABMT_8 Bachelor of Science (Hons) in Automotive Business Management and Technology 5 Elective
CR_TTMGT_7 Bachelor of Science in Automotive Technology and Management 5 Mandatory